Expert Answers about Fleetwood Prowler Travel Trailer
- Replacement Brake Assembly Recommendation for 2004 Fleetwood Prowler Regal 32'
- Best option is to match the part number you found on your trailer. Realistically the 6k and 7k brake assemblies are mostly interchangeable as they both are 12 inch diameter by 2 inch width so either would technically fit, but going with the correct rating gives you a setup that's easiest to fine tune braking power. If you go with an assembly rated too high the magnet is more sensitive and you'll find that the brakes are harder to get the exact amount of braking power. It'll either feel...
view full answer... - Replacement Tires for 2004 Fleetwood Prowler Lynx Travel Trailer
- Typically you want to match the tires that are currently on the trailer. You can also look at the data plate on your trailer which probably lists the tire size. Outside of that there is no way to look up this information. I'm not sure which specific model you have, but I was able to find old pictures of a 2004 Fleetwood Prowler Lynx 722 data plate which lists ST175/80R13 tires.
Assuming this matches your current tires or the data plate, you could use the Karrier ST175/80R13 Radial Trailer...
view full answer... - Recommended Replacement for an RVP 8000 Series AC
- Since your RVP AC is the parent company and owner of Coleman that means they'll have the same wiring so any AC that replaces a Coleman setup will be good.
For your RVP 8000 Series AC I recommend replacing it with the Furrion Chill HE Replacement RV Air Conditioner for Coleman Setup # FR42PV.
The Furrion Chill units are going to be the best ACs on the market and will definitely be a nice upgrade to any trailer. This kit includes a wiring adapter that'll allow you to continue to use your...
view full answer... - Replacement Door Lock for 2005 Fleetwood Prowler Travel Trailer
- Thank you for all of the photos!
According to all of the measurements you took, I recommend the following from Global Link:
- Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option # 295-000019
Attached is a review video for you to check out!
view full answer... - How to Determine if Lippert Electric Stabilizer Jacks Fit Trailer
- I can help you to determine if the Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707 will fit your 2004 Fleetwood trailer, though we do not have any type of dimensions or parts list for any type of year, make and model of trailer.
Instead, what you will need to do is simply go by the mounting hole dimensions, which are 68-11/16" on center. Simply stated, this means your trailer's frame would need to have that spacing for this stabilizer...
view full answer... - Recommended Hub And Drum Kit For A 2008 Fleetwood Prowler Travel Trailer
- When it comes to replacing the hub and drums on your 2008 Fleetwood Prowler Travel Trailer first you need to know what the inner and outer bearing numbers are on your existing hub and drum. I will put a link below showing how to find the inner and outer bearing numbers.
The Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles - 10 inch Diameter - 5 on 4-1/2 # 84546UC3 has an inner bearing # L68149 and an outer bearing # L44649.
The inner bearing # L68149 has an inner diameter...
view full answer... - Replacement Slide-Out Motor Needed for a 2005 Fleetwood Prowler
- If you currently have a Venture slide-out motor with an 18:1 gear ratio then yes, the Lippert Components 18:1 Venture Actuator Slide-Out Motor # LC132682 will work.
If not I will need to know some more specifics on your current motor. Unfortunately manufacturers don't keep these details handy so you will need to physically see what you have.
Attached is a link to our selection of slide-out motors that you can reference.
view full answer... - Lift Kit for 2008 Fleetwood Prowler 250RLS
- From the specifications I was able to find online, your Travel Trailer likely has tandem 3500 lb axles with a 2-3/8 inch axle tube diameter. If this is the diameter of your axle tube, we have the perfect solution that could provide a height increase equal to the axle tube diameter plus the thickness of the leaf spring pack.
If your leaf springs are currently mounted to the underside of your axle, you can relocate the spring packs to the top of the axle tube using an Over/Under Conversion...
view full answer...
Go To Results